• Issue - Exporting corridor template as xml

    I tried exporting a corridor template this morning and received the error message below. The full error message is attached.     
    Patrick L'heureux
    last modified by Patrick L'heureux
  • Holes in corridor, what am i doing wrong?

    I will attache a .VCE file here with a corridor and one template. Is someone can import it and see what i am doing wrong here. I get holes in the corridor at different places and it seems like it has to do with my ali...
    Fredrik Bergstrom
    last modified by Fredrik Bergstrom
  • Feature Request - Stored Cross Sections - View Slope and Input Slope

    There have been some fantastic improvements when it comes to importing pdf cross sections. Thank you! This is very helpful and saves a lot of time.   I have some recommendations to improve the process with worki...
    Patrick L'heureux
    last modified by Patrick L'heureux
  • Power User Group 2.0 Training Materials

      After another successful PUG Power Users Group Conference in April, I am pleased to provide those of you that could not make it to Colorado with the Training Exercises that we went through at the event. I will...
    Alan Sharp
    last modified by Alan Sharp
  • Elevation labels offsetting in random directions

    Elevation labels offsetting in random directions when I'm trying to label a profile on a sheet set.  I have set the offset to 0.30 in, but some of the labels are plotted at -0.03 in.  What could be causing t...
    Matt Eklund
    last modified by Matt Eklund
  • Save the Date - Trimble Business Center - Power User Group - Europe

    2/11/20 12:00 AM
      Due to "Popular Demand" and repeated requests from our Geospatial and Construction Distribution Partners, we have finalized the venue and dates for the first Trimble Business Center - Power Users Group me...
    Alan Sharp
    last modified by Alan Sharp
    Save the Date - Trimble Business Center - Power User Group - Europe
    Back
  • Best Practices for Modifying a TTM

    I had to adjust an old mode lthis morning that either myself or one of my colleagues prepared 4+ years ago. I did not have the original data but I did have the ttm that we provide to the field crews. I needed to adjus...
    Patrick L'heureux
    last modified by Patrick L'heureux
  • How to Set Up TML Status and Access Rockpile Solutions TMLs.docx

    This document describes how to download, install and set up the Rockpile Solutions TML Status application. The application will manage all of your TMLs and notify you when new ones become available or when existing on...
    Alan Sharp
    last modified by Alan Sharp
  • BB - Power Hour Dec.zip

    Here is the Completed Project that we went through in the CEC December 2019 Power Hour if you want to try running the processes yourself following along to the video recording of the event.   The Power Hour cove...
    Alan Sharp
    last modified by Alan Sharp
  • Can a vertical alignment start after the POB of the HAL?

    Regarding this, the vertical alignment in question starts in a vertical curve with the VPI being 11 feet from the start. In other words, while the vertical curve is 680' long, only 351 feet of it are actually part of...
    David Bonds
    last modified by David Bonds
  • Does anyone know if you can breakout a corridor earthwork report to only show left or right of center line?

    I'm trying to decide whether or not the tool will be useful to me from a takeoff perspective digitizing cross sections. Most jobs we run end up being phased based off of an offset from center line and I would like to ...
    Travis Bell
    last modified by Travis Bell
  • Best fit line with curves?

    Hi!   Look at my screendumps. I have a line, 5400m long measured with gps on a atv every second meter. This line i suppose to be my alignment for a corridor so i have to make it smooth. Is there anyway to easy g...
    Fredrik Bergstrom
    last modified by Fredrik Bergstrom
  • APAC Region - Power User Group (PUG) Training for TBC Users

    11/17/19 5:00 PM
    Save The Date! Asia Pacific Regional Power User Group (PUG) Training Trimble Business Center - Construction November 18th - 20th 2019     When / Where Is The Event? Trimble is pleased to announce a...
    Alan Sharp
    last modified by Alan Sharp
    APAC Region - Power User Group (PUG) Training for TBC Users
    Back
  • Plotting Cross Sections

    I was given existing ground surface then did a topo of a section of road built. I want to plot cross sections every 50', horizontal scale to be 20 and vertical to be 10. I am trying to figure out the correct way of ad...
    Pablo Giraldo
    last modified by Pablo Giraldo
  • Is there a way to create a best-fit profile based off a road surface?

    I've got a scanned road surface from which I want to derive a profile/vertical alignment so I can verify slopes and K-values along the road. I know I can elevate a linestring to the scanned surface and turn it into an...
    Mickey Kocemba
    last modified by Mickey Kocemba
  • Corridor by Phase

      We are begining to being ask to run earthwork quantities by Phase (road/highway projects).  I have found to add the subgrade material to another material to have a combine total subgrade surface.  Thi...
    Francisco Guerrero
    last modified by Francisco Guerrero
  • Profile from PDF, import to Businesscenter, Possible?

    I think i have seen that it should be possible to import profile drawings from pdf into BC-HCE (or TBC) and be able to use that profile on an alignment, is that correct? If i can, where is the button?
    Fredrik Bergstrom
    last modified by Fredrik Bergstrom
  • Intersection Template

    HI, I am trying to create an intersection after watching Trimble's Youtube video. I am having trouble with finding or creating an intersection template. Would anyone be willing to share their templates for interstecti...
    Ken Bork
    last modified by Ken Bork
  • US Survey Foot - CADXS Conversion.vct

    This is an example project template File for use with the CAD or PDF Cross Sections to 3D Linework conversion process. The Template was created for TBC v5.2 (as yet unreleased).
    Alan Sharp
    last modified by Alan Sharp
  • Power User Group 3.0 (PUG 3.0) TBC

    Power User Group on TBC (PUG) in Denver - October 22-23-24   Class is off to a great start at 8am on Tuesday morning.  A full house of people ready to learn the latest version of TBC.  People and Deale...
    Scott Bridges
    last modified by Scott Bridges