• Surface - Swap Triangle lock/save

    Is there a way to lock or save the surface after doing a swap triangle work so it won't go back to the original after rebuilding the surface?
    Eric Condemilicor
    last modified by Eric Condemilicor
  • Feature Request project Cleanup

    When cleaning up Cad data imported if we had a command similar to the lyr command in Terramodel it would make cleaning up a file a lot faster, lyr command was set to toggle visibility of a layer off when you clicked o...
    Ben Brown
    last modified by Ben Brown
  • Is there a way to generate a linestring where two surfaces intersect each other?

    I'm trying to generate a linestring where an OG surface intersects my model. I have some blast regions that I need to quantify where the OG intersects the proposed roadway and I want to get a linestring of that inters...
    Rich Joslin
    last modified by Rich Joslin
  • When I create spot elevations on my As-Built Certification/Documentation/Quantification plans I use the "Point Symbol" command to make the tick marks.  How does one plot the symbols when using the dynaview command on sheet view?

    When I create my As-Built Certification/Documentation/Quantification plans I use the "Point Symbol" command to make my tick marks.  How does one plot the symbol's when using dynaview in sheet view?
    last modified by BRUCE FLORA
  • Dynaviews not plotting point symbols

    Issue with Dynaviews  If you create a point label with a symbol, PT#, Elev, Desc and display it from a plotbox into a Dynaview, the symbol does not appear.  The only way I can get this into a document is t...
    Ron Ciccarone
    last modified by Ron Ciccarone
  • Issue w/Create Design/Design Manager in 5.21

    The 5.21 update seems to have created an issue or modified the workflow for producing designs.   Upon the initial setup of the project, the Job Site Manager allows assigning of controllers as usual, ho...
    Richard Tyndall
    last modified by Richard Tyndall
  • Cross Section Takeoff - Navigation through View SHeets

    Is there a way to set page up and page down on the keyboard to cycle through sheets when there is an active sheet view open?
    Patrick L'heureux
    last modified by Patrick L'heureux
  • TBC - Layered PDF

    Is there a way to get a layered pdf when printing a sheet or plan set in TBC?                               Thanks!
    Eric Schmeusser
    last modified by Eric Schmeusser
  • Problem Installing 5.21

    I've downloaded 5.21 but can't get it installed.  Each time I get to this point and it gets some kind of error and shuts down.  See screenshot below.  Any ideas on where to go from here?  I'll try ...
    Ben Wall
    last modified by Ben Wall
  • Where to place Vertical design rules?

    It seems that the rule fades out as you move away from the location it was placed. I am working with a street and using it to elevate the gutter and top of curb. I placed the rule at the end of the street but as I mov...
    Tom Dew
    created by Tom Dew
  • Feature Request - Utilities - Tie Node Rims to a Surface

    Please consider adding an option that would allow a user to tie the rim elevation of a node to a surface.   This would help when designing and when changing the model to make sure that entities are updating corr...
    Patrick L'heureux
    last modified by Patrick L'heureux
  • How can I transfer a Trimble Access "ground coordinate" based calibration to Siteworks and GCS900?

    I have a project where the local DOT has asked that we utilize a single "shared" base station. I have set up our SPS855 base station using a known point coordinate that they had given me, as well as using their extern...
    Brandon Tobias
    created by Brandon Tobias
  • Customizing Ribbons Crashes TBC Version 5.21

    I installed the TBC 5.21 today and noticed that customizing my ribbons crashes my TBC.
    Eric Condemilicor
    last modified by Eric Condemilicor
  • Is there a way to have TBC place the name of a closed feature (rectangular or polygon) in the centroid of the feature after processing the feature codes. For example placing the name St. John's Church within the drawing of the building?

    For example placing the name of the feature e.g. Harry's Bar within the drawing of the bar. The name should be entered while gathering data in the field. This would lessen the chances of wrong naming.
    Trevor Isaac
    created by Trevor Isaac
  • TBC v5.21 LOCKING UP

    I was wondering if anyone else was having issues with TBC V5.21 locking up.  I am creating a site and I am using point cloud data and I have had it lock up three times in a row when trying to offset a line. ...
    Ben Ryschon
    created by Ben Ryschon

    Anybody know if TCC is down?
    Ben Ryschon
    last modified by Ben Ryschon
  • Alignment Report Using PI Stations

    We use a online plan app that we upload our alignments.  The alignments are in CSV format and the PI N/E with radius is used.  For tangent lines only need the N/E.  The Geometry Report comes close, I wo...
    Francisco Guerrero
    last modified by Francisco Guerrero
  • Plan Sets - Is there a way to copy sheet sets?

    Is there a way to copy sheet sheets? If not enhancement request. I have my sheet set all set up with a dynaview collection. All I want to do is copy the sheet set and change the view filter that is active for the shee...
    Patrick L'heureux
    last modified by Patrick L'heureux
  • Replacement For SPS930?

    Any hints as to when we might see an updated version (or replacement) for the SPS930? How about an SX10 style instrument? The current SPS series is about 12 years old and in the field the expectations for scanning, la...
    Marshall Cant
    created by Marshall Cant
  • Which TBC Edition/Module Do I Need To Model a Penstock?

    I have to model a 3.1m diameter Penstock that is basically encased in a concrete structure with an additional 2 conduits running beside it that are also encased in the same concrete structure. The Penstock has several...
    Marshall Cant
    last modified by Marshall Cant